- 5.4.8 TESTOUT LAB CONFIGURE THE ISCSI INITIATOR INSTALL
- 5.4.8 TESTOUT LAB CONFIGURE THE ISCSI INITIATOR UPDATE
- 5.4.8 TESTOUT LAB CONFIGURE THE ISCSI INITIATOR PRO
- 5.4.8 TESTOUT LAB CONFIGURE THE ISCSI INITIATOR SOFTWARE
- 5.4.8 TESTOUT LAB CONFIGURE THE ISCSI INITIATOR FREE
I’m using iSLB in this example, but you can use anything. You need to make this storage available to CorpFiles16 users. You created an iSCSI storage area network (SAN) on the CorpiSCSI server.
5.4.8 TESTOUT LAB CONFIGURE THE ISCSI INITIATOR PRO
Go to your storage network and configure necessary communications. TestOut Server Pro 2016 - 5.4.8 - Lab - Configure the iSCSI Initiator STUDY Flashcards Learn Write Spell Test PLAY Match Gravity You work as the IT administrator for a growing corporate network. Then click the green “+” to add an iSCSI target.Įnter the iSCSI target name, IP and port. I’m not configuring any.Ĭlick “Set Boot Parameters” under iSCSI vNICs.Ĭhoose the Initiator pool, and IQN pools created in the beginning (Note, we could have also created the pools from here, I just like to do them first). If you wanted to create an iSCSI Adapter Policy for some additional parameters, here is where you do so.
Give it a name, set the Overlay vNIC as the one we created earlier, set the native VLAN to the iSCSI VLAN.ĭo NOT assign MAC addresses here!! Will not boot if you do!! Think of this as a virtual placeholder for the iSCSI traffic. This is easily confused with the vNIC created earlier, but this is completely separate and actually isn’t really a vNIC, it’s an iSCSI bootable firmware table (iBFT) used of iSCSI boot. Notice the ordering is now sequential starting at “1”. Servers > Service Profile Templates > Template > Network tabĭrag all vNIC on the left to vCon 1 on the right. If using VMware, set the adapter policy accordingly SAN > Pools > IQN Pools > Create IQN Suffix Pool Lan > Pools > IP Pool iscsi-initiator-pool > Create Block of IP Addresses This might be due to the hardware I was using (Dell PowerEdge 2950), I’m not sure.Follow these steps to boot from iSCSI in UCS Create a pool of ISCSI Initiator IP Addresses
5.4.8 TESTOUT LAB CONFIGURE THE ISCSI INITIATOR INSTALL
Using the datastore install method I discovered here:Īnd now it seems to run a little closer to the article described.
5.4.8 TESTOUT LAB CONFIGURE THE ISCSI INITIATOR UPDATE
Note I had a couple of problems when I was running 6.5.0 build 48877370 but I did the (free) update to 6.5.0 update 1 5969303 which I got from here:Īnd installed using the zip-file install advice here: This does not 100% correspond with the picture under the port group setup. One thing which caught me out (and at least one other person in the comments) note the line:Īt the port group level: A single NIC is set as active. Now is the fun bit, where I break it again to figure out exactly what all the different options do. To do so select Networking > VMkernel NICs > Add VMkernel NIC.įirstly, THANK YOU – I’m on page 1 with ESXi, just learning from the start, so I didn’t 100% understand everything I was doing, but following your step by step got me running iSCSI. Networking ^įirst, we need to add a VMkernel network interface card (NIC) to our system so the ESXi host can connect to the remote storage device. Note that if you're managing a vCenter server-based VMware infrastructure, you'll still need an Adobe Flash plugin. While inside the iscsi path, it is now possible to create the iscsi target with a name. You don't need plugins, and you can just connect through the URL (replace "ip_of_ESXi" with your installation's IP address). In order to create the iSCSI Target, we have to move into the iSCSI path in our server.
5.4.8 TESTOUT LAB CONFIGURE THE ISCSI INITIATOR SOFTWARE
One advantage of the HTML5 host client is that you don't need to install any software on your management computer because you connect via a web browser. We'll be using the new HTML5 host client, which is different than the old Windows client. Network switch between shared storage and the ESXi host.Shared storage offering the iSCSI protocol.At least one ESXi host with two physical NICs (management and storage traffic).And you don't have the possibility to move VMs from one host to another using vMotion technology. However, because you don't have a central management server (VMware vCenter server), you can only manage your VMs individually, host by host.
5.4.8 TESTOUT LAB CONFIGURE THE ISCSI INITIATOR FREE
You can then have several free ESXi hosts accessing the same datastore.